JT Tinker Posted June 16 Share Posted June 16 (edited) Trip: Snow Creek - The Chisel (North Face, 5.9) Trip Date: 06/14/2024 Trip Report: After stumbling across Jplotz's photos of the Chisel on SummitPost taken in 2006, I was inspired by the aesthetics of this pinnacle and the lack of information about it. (Edit: I found JPlotz's CC post shortly after writing up my own report! Turns out their ascent was in 2004.) Jplotz, 2006: The photo that captured my imagination Photo from 6/14/24 Working with only the 2006 photos, a brief mention in the Cascade Alpine Guide, and a location pin on Caltopo (later discovered to be inaccurate) my buddy Sam and I set off for a Cascadian adventure. We approached via the Wedge Mountain Trail, bushwhacking and scrambling south along the ridge to the point where we would drop down into the 4th class terrain and descend the 500 feet to the base of the Chisel. The bushy ridge of Wedge Mountain, looking north. The tower in the middle is not the Chisel. In hindsight, the more sane approach is to take the Snow Lakes Trail and ascend a gully (unless you have a hankering for a scrappy, scrambly day out) even though the mileage and elevation gain are higher. This way, you can avoid most of the schwacking, the loose descent off the ridge, and the heinously overgrown road to the Wedge Mtn. Trailhead. The second crux of the day (the first being the road) was locating the Chisel. Caltopo's pin is about 400 feet too far north, and this caused some confusion as we continued down the ridge with no Chisel in sight. After traversing a little farther and scrambling up to a viewpoint, we finally laid eyes on the pinnacle and felt a mixture of stoke and worry as we realized how much kitty litter and pine needle-strewn 3rd and 4th class terrain we would have to descend to reach our objective. The Chisel reveals itself! We hemmed and hawed for a few minutes, then started carefully down-scrambling. We made one rap off a tree, then roped up and traversed south across a dense 45˚ forest slope, using the trees for a natural running belay. Just when it felt like we must have passed the formation, Sam shouted back to me that we were close! Soon we were back on rock, scrambling to the base of the climb. We took a short break to settle in and rack up, then started up the real climbing. I led the first short step to the big belay ledge, a hand crack behind a flake. Up next was the 75' 5.9 pitch that I had seen referenced but never photographed. I was surprised by how protectable and high-quality it looked. 75 feet of 5.9 crack! I started up the wide layback, noting how much the lichen-crusted rock reduced the friction beneath my feet. At a good stance, I placed gear and moved into a section of good hands followed by good fists. More laybacking on flakes and solid gear led to the final section of hands with increasingly abundant and positive face holds. Topping out, I whooped with delight and stoke on the fun lead and spectacular position. I brought Sam up, and we took a moment to enjoy the views and take photos. There are three bolts at the top, an assortment of rusty 1/4"ers. We replaced the old tat and equalized the two best bolts, backing them up to a nut. Woohoo! Sam on rappel The scramble up and out was straightforward enough, though accompanied by many laments of the Wedge Mtn approach. Burgers in Leavenworth capped off an unforgettable day out! We initially believed we were the first to climb this feature since 2004, but the JPlotz TR reported a hole count of one at the summit and we found three. If you climbed the Chisel after 2004 and before us, reply and tell us about it! The little summit block of Wedge, a small bonus on the day Gear Notes: If you want to sew it up and have a solid anchor: Singles 4 to 0.4 Doubles 2 to .75 Approach Notes: Wedge Mountain approach is much more bushwhacking and scrambling. Snow Lakes Trail is probably much more straightforward than what we did, but longer. Edited June 16 by JT Tinker Found the JPlotz (telemarker) CC report from 2004. 7 1 2 Quote Link to comment Share on other sites More sharing options...
Alisse Posted July 10 Share Posted July 10 Love it! Thanks for sharing! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.